Our advantage
Global Logistics
We have a 10-year logistics and express cooperation agreement, so our products can be shipped to any place in the world.
Brand new and original
Our products are imported in bulk from the place of origin. Because of the cooperative relationship, our products are all original and 100% new.
24-hour service
We provide 7*24 hours service to our customers. We will be there whenever you need us.
Price advantage
All our products are priced very favorably because we have our own warehouse and supply.
| Company Information | |||
| [email protected] | |||
| Mobile | +8615980777398 | ||
| +8615980777398 | |||
| 15980777398 |

The Siemens 6AG2136-6PA00-1BC0 SIPLUS ET 200SP F-PM-E Safety Power Module is a fail-safe power module designed for safety-related applications within the Siemens SIMATIC ET 200SP distributed I/O system. It provides controlled, safety-oriented switching of 24 V DC load power for digital output modules, helping industrial automation systems implement defined shutdown functions when hazardous operating conditions are detected.
This module belongs to the SIPLUS extreme product family and is based on the standard Siemens 6ES7136-6PA00-0BC0 F-PM-E module. Its conformal coating and extended environmental specifications make it suitable for applications where additional protection against challenging operating conditions is required.
The F-PM-E uses PROFIsafe communication within an appropriately configured safety automation system. It supports the safe shutdown of digital outputs (DQ) and fail-safe digital outputs (F-DQ), with safety capability up to PL D/SIL 2 or PL E/SIL 3, depending on the system architecture and applicable safety configuration.
The module provides two safe digital inputs and one safe digital output using the PPM configuration. Its nominal supply voltage is 24 V DC, and the product designation identifies an 8 A power module.
The 6AG2136-6PA00-1BC0 is intended for applications where standard process control and functional safety must work together. It can help separate safety-related power control from ordinary output operation, allowing a safety controller to initiate defined shutdown actions without relying solely on standard automation logic.
For equipment selection and replacement, engineers should verify the complete order number, compatible ET 200SP BaseUnit, safety configuration, firmware requirements, and environmental conditions.
| Parameter | Specification |
|---|---|
| Brand | Siemens |
| Product Family | SIPLUS extreme |
| Product Series | SIMATIC ET 200SP |
| Model | 6AG2136-6PA00-1BC0 |
| Product Type | F-PM-E Safety Power Module |
| Product Designation | F-PM-E PPM 24VDC |
| Base Module | 6ES7136-6PA00-0BC0 |
| Rated Supply Voltage | 24 V DC |
| Permissible Supply Voltage | 20.4–28.8 V DC |
| Rated Current Designation | 8 A |
| Safety Communication | PROFIsafe |
| Safe Digital Inputs | 2 |
| Safe Digital Outputs | 1 PPM |
| Main Function | Safe shutdown of DQ and F-DQ load groups |
| Safety Capability | Up to PL D/SIL 2 or PL E/SIL 3, depending on configuration |
| Conformal Coating | Included |
| Operating Temperature | -30°C to +60°C |
| Short-Term Temperature Capability | Up to +70°C for 10 minutes, subject to specified conditions |
| Reverse Polarity Protection | Yes |
| Compatible BaseUnit | Type C0 |
| Firmware Update | Supported |
| Dimensions Provided | 20 × 72 × 55 mm |
| Weight Provided | 0.084 kg |
| System | Siemens ET 200SP distributed I/O |
Note: Dimensions and weight are the supplied listing values. Confirm the exact module and packaging measurements before using them for installation or logistics planning.
The Siemens F-PM-E module is designed to provide safety-related control of load power within an ET 200SP distributed I/O station. Its operation is based on the coordination of the safety controller, PROFIsafe communication, the F-PM-E module, and the connected output modules.
In a conventional automation system, digital output modules switch electrical signals to operate devices such as contactors, solenoid valves, and other actuators.
In safety-related applications, simply switching off a standard PLC output may not provide the required level of protection. A dedicated safety function is needed to place the controlled equipment into a defined safe state.
The F-PM-E provides a safety-oriented power switching function for compatible DQ and F-DQ load groups. When a valid safety shutdown command is issued, the module can interrupt the relevant 24 V DC load supply according to the configured safety design.
This function can be used as part of machine safety strategies involving emergency stops, protective doors, and other safety-related conditions.
PROFIsafe is a safety communication protocol designed for transmitting safety-related data over supported industrial communication networks.
The F-PM-E operates within a PROFIsafe-compatible ET 200SP safety architecture. The safety controller evaluates safety signals and sends the required safety commands through the configured communication system.
The module then performs its assigned safety power-management function.
PROFIsafe communication helps support safety-related data exchange, but the overall safety performance depends on the complete system design, including the controller, field devices, network configuration, wiring, diagnostics, and validation.
The 6AG2136-6PA00-1BC0 provides two safe digital inputs. These inputs can be incorporated into the safety architecture for receiving compatible safety-related signals.
Depending on the application design, safety devices such as switches or other compatible sensors may provide signals that are evaluated by the safety system.
Input wiring, signal evaluation, test-pulse configuration, and diagnostic behavior must follow the applicable Siemens documentation and the requirements of the selected safety application.
The module provides one safe digital output using the PPM configuration.
PPM refers to a switching arrangement in which the output provides the positive supply potential to the connected load under the defined operating conditions. This output arrangement must be considered when selecting compatible wiring, output modules, and load circuits.
Correct connection and configuration are essential for ensuring that the intended safety function operates as designed.
As a SIPLUS extreme product, this module includes conformal coating and an extended operating-temperature specification.
The coating provides additional protection for electronic assemblies under specified environmental conditions. It does not mean that the module can be installed without regard to humidity, condensation, contamination, or enclosure requirements.
The specified temperature limits and installation conditions should always be followed.
The Siemens 6AG2136-6PA00-1BC0 plays a specialized role in distributed safety automation. It provides a controlled power-management function for output circuits within an ET 200SP station.
The module is designed to operate within a compatible Siemens safety automation system. A safety-capable controller evaluates input signals from safety devices and determines whether the machine can continue operating.
When a safety condition requires shutdown, the controller communicates the appropriate command through the configured PROFIsafe architecture. The F-PM-E then performs its assigned safe power-switching function.
This approach allows safety-related functions to be coordinated with the wider machine-control system.
The ET 200SP platform uses modular distributed I/O stations. Different electronic modules can be installed in a station to handle standard digital signals, analog measurements, and safety-related functions.
The F-PM-E provides the safety-related power-management function for compatible output groups. It should be selected together with the appropriate BaseUnit and supported I/O modules.
Industrial machines often combine ordinary process automation with safety-related control. Standard PLC logic may regulate speed, sequence operations, and monitor production, while a safety controller handles emergency stops and protective-device signals.
The F-PM-E supports this separation by providing a dedicated safety power-switching function.
A clear distinction between standard and safety functions makes system design, testing, troubleshooting, and maintenance more manageable.
The 6AG2136-6PA00-1BC0 can be used in ET 200SP installations where controlled shutdown of 24 V DC output power is part of the machine safety design.
Production machines often contain motors, pneumatic actuators, valves, and other devices that must enter a safe state when a protective condition occurs.
The F-PM-E can be incorporated into the safety architecture to support shutdown of compatible output load groups.
Packaging machines use multiple actuators for feeding, sealing, cutting, and product handling. Safety-related power management is important when operators need access to moving or potentially hazardous machine areas.
The module can form part of a safety system that coordinates output power shutdown with emergency-stop and protective-device functions.
Conveyor installations may include multiple drives, contactors, and actuator circuits distributed across different machine sections.
A safety controller can monitor protective devices and initiate the required shutdown sequence. The F-PM-E may be used to manage compatible 24 V DC output power within the ET 200SP station.
Automated assembly equipment often combines robotic movement, pneumatic tooling, sensors, and distributed I/O. Safety functions must coordinate the behavior of these devices when a hazardous condition occurs.
The F-PM-E can support safety-related output power control as part of a validated machine safety design.
Industrial process equipment may use valves, actuators, and other electrical devices that require safety-related shutdown functions.
The module can be incorporated into suitable distributed I/O systems where the output power architecture and safety requirements match its capabilities.
The SIPLUS extreme design and conformal coating make this module relevant to installations that require extended environmental specifications compared with standard ET 200SP equipment.
The actual suitability depends on temperature, humidity, condensation, contamination, and the installation enclosure.
Correct installation is essential for the module’s electrical performance and safety-related operation.
Before installation, confirm that the module is being used in a supported Siemens ET 200SP configuration.
Check the safety controller, firmware versions, PROFIsafe configuration, compatible electronic modules, and the required BaseUnit type.
The specified module uses a C0-type BaseUnit. Do not substitute a different BaseUnit without confirming compatibility in the manufacturer’s documentation.
The module has a nominal supply voltage of 24 V DC, with a permissible range of 20.4–28.8 V DC.
Verify that the power supply can support the connected load groups and that voltage drop remains within the permitted range.
Reverse polarity protection is specified, but correct polarity and wiring are still required for reliable operation.
The product designation identifies an 8 A F-PM-E power module. Engineers should verify the applicable current limits and load-group requirements in the technical documentation.
Confirm that the connected DQ and F-DQ modules, field devices, wiring, and protective devices are compatible with the intended power arrangement.
The module must be integrated into a supported safety configuration. This includes the required hardware configuration, safety address, communication settings, and safety program.
The safety controller and module must be configured consistently. Incorrect PROFIsafe parameters may prevent communication or cause the system to enter a safe state.
The specified operating temperature is -30°C to +60°C, with a short-term capability of up to +70°C for 10 minutes under the stated conditions.
Maintain suitable ventilation and protect the module from environmental conditions outside its specified limits.
Conformal coating provides additional environmental protection but does not replace proper enclosure design and installation practices.
After installation, test the complete safety function rather than checking only whether the module powers up.
Verify the connected safety inputs, PROFIsafe communication, output shutdown behavior, diagnostic messages, and response to relevant fault conditions.
Document the test results and confirm that the complete installation meets the required safety performance level.
The F-PM-E is intended to operate as part of an ET 200SP distributed safety I/O station.
| Component | Function | Integration Considerations |
|---|---|---|
| Siemens SIMATIC ET 200SP station | Distributed I/O platform | Confirm supported station configuration |
| Siemens F-CPU | Executes safety-related control logic | Must support the required safety configuration |
| ET 200SP BaseUnit type C0 | Provides mechanical and electrical module connection | Verify the specified BaseUnit type |
| PROFIsafe network | Transfers safety-related data | Configure safety addresses and communication parameters |
| ET 200SP DQ modules | Control standard digital output loads | Verify supported power-group arrangement |
| ET 200SP F-DQ modules | Provide fail-safe digital outputs | Confirm supported module and load configuration |
| Safety switches and sensors | Detect hazardous machine conditions | Select compatible devices and validate input wiring |
| 24 V DC power supply | Provides operating voltage | Maintain the specified voltage range and adequate current capacity |
| Contactors and solenoid valves | Operate machine actuators | Confirm load ratings and safe-state requirements |
| Engineering software | Configures hardware and safety logic | Use supported Siemens engineering tools and versions |
The components listed above are examples of equipment that may form part of a complete installation. They are not necessarily included with the F-PM-E module.
When replacing a Siemens safety power module, engineers should compare the exact order number and the complete safety-system configuration. A standard power module or ordinary digital output module is not an equivalent substitute for a fail-safe power module.
| Related Model or Product | Description | Replacement Considerations |
|---|---|---|
| 6ES7136-6PA00-0BC0 | Standard SIPLUS base-design F-PM-E power module | Related base model; verify environmental specifications and exact configuration |
| 6AG2136-6PA00-1BC0 | SIPLUS ET 200SP F-PM-E 24VDC/8A PPM | SIPLUS version with conformal coating and extended environmental specifications |
| ET 200SP F-DQ modules | Fail-safe digital output modules | May complement the F-PM-E but do not automatically replace its power-management function |
| ET 200SP F-DI modules | Fail-safe digital input modules | Used for safety signal acquisition rather than power-group shutdown |
| Siemens S7-1500F CPU | Safety-capable controller family | Must be checked for compatibility with the existing hardware and safety program |
Before selecting a replacement, compare:
A standard ET 200SP module should not be used as a substitute for a safety module unless the complete safety design has been reassessed and approved.
The F-PM-E provides a defined function for safe shutdown of compatible DQ and F-DQ load groups, supporting safety-related machine-control architectures.
PROFIsafe communication allows the module to participate in a compatible Siemens safety automation system.
The module provides two safe digital inputs for integration into the supported safety configuration.
The single PPM safe digital output supports the module’s specified fail-safe power-management functionality.
The SIPLUS version includes conformal coating and extended environmental specifications, supporting use in demanding industrial installations.
The module can be integrated into a modular distributed I/O station, allowing safety-related functions to coexist with other compatible automation modules.
When used with a suitable safety controller and validated configuration, the F-PM-E can support machine safety functions involving emergency stops, protective devices, and controlled shutdown of electrical loads.
It is a SIPLUS ET 200SP F-PM-E fail-safe power module designed for safety-related 24 V DC power switching in compatible distributed I/O systems.
Its main function is to provide safe shutdown of compatible DQ and F-DQ output load groups within a configured ET 200SP safety architecture.
The nominal supply voltage is 24 V DC. The specified permissible range is 20.4–28.8 V DC.
The module provides two safe digital inputs and one safe digital output using the PPM configuration.
PROFIsafe is a safety communication protocol used to transfer safety-related data over supported industrial networks. The module uses PROFIsafe within a compatible safety automation system.
The product is specified for safety applications up to PL D/SIL 2 or PL E/SIL 3, depending on the system configuration and applicable safety architecture. The rating of the individual module does not automatically establish the safety level of the complete machine.
The 6AG2136-6PA00-1BC0 is the SIPLUS version based on the 6ES7136-6PA00-0BC0. The SIPLUS version includes conformal coating and extended environmental specifications.
The specified usable BaseUnit type is C0. Always verify the exact BaseUnit and station configuration against the manufacturer’s compatibility documentation.
It can be used with compatible DQ and F-DQ output arrangements as defined by the system design. Compatibility, power-group configuration, and safety behavior must be checked for the specific modules involved.
Verify the complete order number, physical condition, BaseUnit compatibility, supply voltage, safety I/O configuration, firmware requirements, conformal coating, and environmental specifications. For a safety-critical installation, confirm that the replacement is suitable for the validated safety configuration.
The Siemens 6AG2136-6PA00-1BC0 is a safety-related automation component, so procurement should focus on exact model identification and configuration compatibility.
Before ordering, compare the product label with the installed module and confirm the complete order number. Check that the unit is the SIPLUS version rather than a standard ET 200SP module with a similar product designation.
For used or surplus equipment, request clear photographs of the front label, terminals, and housing. Confirm the module’s condition, storage history, and available testing information. The presence of a conformal coating should not be treated as proof that a unit is suitable for every environmental condition.
During maintenance, inspect the module and BaseUnit for signs of overheating, contamination, mechanical damage, or loose connections. Review diagnostic information and verify that the PROFIsafe communication and safety program remain correctly configured.
After replacement, carry out the required safety validation and document the results. Because this module participates in safety-related functions, any hardware or configuration change should be reviewed under the site’s functional-safety procedures.
The Siemens 6AG2136-6PA00-1BC0 SIPLUS ET 200SP F-PM-E Safety Power Module is designed for safety-related 24 V DC power management in Siemens ET 200SP distributed I/O systems. With PROFIsafe integration, two safe digital inputs, one PPM safe digital output, and support for safe shutdown of compatible DQ and F-DQ load groups, it provides a dedicated function within industrial machine safety architectures.
Its SIPLUS construction includes conformal coating and extended environmental specifications. For installation, maintenance, and replacement, engineers should verify the BaseUnit type, power requirements, safety configuration, firmware compatibility, and environmental conditions to ensure reliable operation within the complete safety system.