Product Overview

The Ingersoll Rand 47560118001 39218193 High Temperature Grease is an industrial lubrication product associated with Ingersoll Rand compressor and motor maintenance. Its lubricant reference, 39218193, is identified as genuine Ingersoll Rand high-temperature motor grease and is used in specified equipment maintenance applications.

Lubrication plays an important role in the reliability of industrial rotating equipment. Electric motors, bearings, and other moving components operate under mechanical loads and temperature variations. Without the correct lubricant, friction and wear can increase, potentially leading to elevated operating temperatures, vibration, bearing damage, and unplanned maintenance.

Ingersoll Rand 39218193 is associated with motor-bearing lubrication requirements in certain compressor configurations. Equipment documentation identifies this reference as a recommended motor grease for particular motor applications. The correct lubricant selection depends on the motor specification, operating frequency, bearing design, and maintenance instructions.

This product is intended for maintenance personnel responsible for industrial compressors and related rotating machinery. Using the specified lubricant helps maintain consistency in scheduled maintenance and reduces the risk of introducing an unverified grease formulation into a bearing system.

The complete product designation supplied for this listing is 47560118001 39218193. The lubricant reference 39218193 is the primary identifier confirmed in the available product information. Buyers should verify the complete packaging label and applicable equipment parts documentation before ordering.

Technical Specifications

Note: Detailed lubricant properties and operating limits should be confirmed using the current product technical data sheet and the equipment manufacturer’s maintenance instructions. The supplied dimensions and weight are listing information, not a substitute for the package label.

Function and Working Principle

High-temperature grease is designed to provide lubrication between moving mechanical surfaces under specified operating conditions. It helps maintain a protective lubricant film, reducing friction and limiting direct contact between bearing components.

1. Bearing Lubrication

Bearings support rotating shafts and allow them to move with controlled friction. During operation, rolling elements travel along bearing raceways, creating contact zones that require appropriate lubrication.

A suitable grease helps separate these surfaces and reduce wear. For electric motor bearings, the correct grease must match the bearing design, operating speed, temperature, and lubrication interval.

Ingersoll Rand 39218193 is identified in equipment maintenance information as a motor grease for specified applications. It should be used only where the equipment documentation calls for this lubricant.

2. Friction and Wear Reduction

Friction is unavoidable in mechanical systems, but suitable lubrication helps reduce friction-related energy loss and surface wear.

The grease forms a lubricating layer between moving surfaces. This layer supports smoother bearing operation and helps protect contact surfaces during normal operating conditions.

Incorrect grease selection, insufficient lubrication, or excessive grease application can all affect bearing performance.

3. Thermal Stability

Motor bearings may experience temperature changes caused by rotational speed, mechanical loading, ambient conditions, and operating duration.

A lubricant intended for elevated-temperature applications must retain appropriate consistency and lubrication performance within its specified operating range.

The term “high temperature” should not be interpreted as permission to use the grease in every hot environment. Actual temperature limits must be checked against the current lubricant documentation.

4. Corrosion and Oxidation Protection

Industrial grease can help protect bearing surfaces from corrosion and oxidation when its formulation and application are suitable.

Maintaining a clean lubricant supply is important. Dust, moisture, incompatible grease, and other contaminants can reduce lubrication effectiveness and contribute to premature bearing deterioration.

5. Support for Preventive Maintenance

Scheduled lubrication is an important part of industrial motor maintenance. Applying the correct lubricant at the specified interval helps maintenance teams manage bearing condition and reduce the likelihood of lubrication-related failures.

The required quantity and relubrication interval must follow the motor or compressor maintenance procedure rather than a general grease-maintenance schedule.

Role in Industrial Compressor Maintenance

The 39218193 lubricant reference is associated with Ingersoll Rand motor maintenance. Its role is to support the lubrication requirements of specified motor-bearing arrangements used in compressor installations.

Motor Bearing Maintenance

Electric motors operate under continuous or intermittent mechanical loads. Their bearings must maintain stable shaft support while accommodating rotational movement.

Correct grease selection helps maintain bearing lubrication and supports reliable motor operation. Maintenance personnel should check the motor’s grease specification before applying 39218193.

Compressor Reliability

An industrial compressor depends on the coordinated operation of its motor, compression elements, cooling system, and control equipment. Motor-bearing problems can affect the reliability of the overall compressor installation.

Using the specified lubricant as part of a planned maintenance program helps maintain the motor’s lubrication requirements.

Maintenance Standardization

Facilities operating multiple compressors often standardize spare parts and consumables to simplify inventory management.

Retaining the complete Ingersoll Rand lubricant reference helps maintenance teams identify the requested grease and distinguish it from other lubricants used in compressor systems.

Industrial Applications

1. Ingersoll Rand Air Compressor Motors

The primary application associated with 39218193 is specified Ingersoll Rand motor-bearing maintenance. Before use, technicians should verify the compressor model and motor lubrication instructions.

2. Electric Motor Bearings

The lubricant reference is associated with motor grease applications. It may be used for the bearing arrangements identified in the relevant equipment documentation.

Bearing type, speed, temperature, and lubrication quantity must be considered before application.

3. Industrial Compressor Service Programs

Preventive maintenance programs often include inspection, cleaning, lubrication, and replacement of consumable components.

The correct grease helps technicians complete the lubrication portion of the service procedure using the specified material.

4. Rotating Equipment Maintenance

Industrial facilities may maintain motors, pumps, fans, and other rotating equipment as part of their general maintenance activities. However, the presence of similar bearing arrangements does not automatically establish compatibility with 39218193.

Always compare the lubricant requirements of the individual machine before using this product outside its documented Ingersoll Rand applications.

5. Scheduled Motor Maintenance

For equipment operating over extended periods, lubrication records help maintenance teams track service intervals and identify recurring problems.

Recording the lubricant reference, quantity, service date, and equipment identification can improve maintenance consistency.

Installation and Maintenance Guidelines

Grease application is a maintenance operation that requires attention to equipment specifications, cleanliness, and safe working procedures.

1. Verify the Required Lubricant

Before opening the container, confirm that the motor or compressor documentation specifies Ingersoll Rand 39218193 or the corresponding lubricant specification.

Do not assume that every Ingersoll Rand motor uses the same grease. Some equipment configurations may require different lubricants according to motor frequency, bearing design, or production specification.

2. Prepare the Equipment

Before performing maintenance, shut down the equipment and isolate the electrical supply according to the applicable lockout/tagout procedure.

Allow rotating components to stop completely. Follow the equipment manufacturer’s safety instructions before accessing bearing lubrication points.

3. Clean the Lubrication Area

Remove dirt and contaminants from the grease fitting and surrounding area before application.

Clean tools and dispensing equipment help prevent dust, moisture, and foreign materials from entering the bearing housing.

4. Apply the Specified Quantity

Use the grease quantity and application method specified in the motor maintenance instructions.

Excessive grease can cause churning, increased bearing temperature, seal damage, or grease leakage. Insufficient grease may leave bearing surfaces inadequately lubricated.

5. Avoid Mixing Different Greases

Do not mix 39218193 with another grease unless compatibility has been confirmed by the lubricant manufacturer or equipment documentation.

Different grease formulations may use different base oils, thickeners, and additive systems. Incompatible combinations can change consistency and reduce lubrication performance.

6. Monitor Bearing Condition

After maintenance, observe the motor for abnormal temperature, vibration, noise, or grease leakage.

Unusual operating conditions should be investigated rather than corrected simply by adding more grease.

7. Maintain Service Records

Record the product reference, quantity applied, equipment identification, and service date.

These records help maintenance personnel track lubrication intervals and maintain consistency across compressor installations.

Compatible System Components

The lubricant is used as part of a broader equipment maintenance process. The following components and systems are relevant to its application.

These items describe the maintenance environment and are not necessarily included with the grease product.

Lubricant Identification and Replacement Considerations

The Ingersoll Rand 39218193 reference is identified as high-temperature motor grease. Some product information associates it with Mobilith SHC 220. However, a replacement lubricant should not be selected based only on a similar product name.

Before considering an alternative, compare:

Important Note About Motor Frequency

Equipment maintenance documentation may specify different motor greases for different electrical-frequency configurations.

For example, one Ingersoll Rand compressor manual identifies Mobilith SHC 220 (39218193) for certain 60 Hz motors, while listing a different grease for 50 Hz motors.

This is why the equipment nameplate and maintenance manual should take priority over general product descriptions. Do not substitute grease without confirming the exact motor requirements.

Key Advantages

Specified Industrial Motor Lubricant

The 39218193 reference is identified as Ingersoll Rand motor grease for designated maintenance applications.

Support for Bearing Lubrication

Suitable grease application helps maintain a lubricating film between bearing contact surfaces and supports normal bearing operation.

High-Temperature Lubrication Application

The product is identified as high-temperature grease. Its actual operating limits must be checked against the current lubricant documentation.

OEM Parts Identification

Using the Ingersoll Rand part reference helps maintenance teams identify the intended lubricant and maintain consistent purchasing records.

Support for Preventive Maintenance

The lubricant can be incorporated into equipment maintenance procedures where 39218193 is specified, helping technicians organize scheduled motor lubrication.

Industrial Compressor Maintenance

The product is associated with Ingersoll Rand compressor and motor service requirements, making accurate identification important for compressor maintenance inventories.

Technical FAQs

1. What is Ingersoll Rand 39218193?

Ingersoll Rand 39218193 is a high-temperature grease identified as motor grease. It is used in specified Ingersoll Rand equipment maintenance applications.

2. What is the function of 39218193 High Temperature Grease?

Its primary function is to lubricate designated motor bearing arrangements. Suitable grease helps reduce friction and wear between moving bearing surfaces.

3. Is 39218193 associated with Mobilith SHC 220?

Yes. Equipment maintenance information and lubricant listings associate 39218193 with Mobilith SHC 220. Always confirm the product label and the current equipment lubrication specification.

4. Can this grease be used for all Ingersoll Rand compressors?

No. Lubricant requirements vary according to compressor model, motor configuration, and operating conditions. Check the applicable maintenance manual before use.

5. Can 39218193 be used in both 50 Hz and 60 Hz motors?

Do not assume so. Some Ingersoll Rand maintenance documentation specifies different motor greases for 50 Hz and 60 Hz configurations. Confirm the motor’s exact requirements before application.

6. Why is the correct grease important for motor bearings?

Correct grease helps maintain lubrication between bearing surfaces, reduce friction-related wear, and support reliable motor operation.

7. Can 39218193 be mixed with other industrial greases?

Mixing should be avoided unless compatibility has been confirmed. Different thickener and base-oil combinations may produce unsuitable lubrication characteristics.

8. How much grease should be applied?

The correct quantity depends on the motor and bearing design. Follow the equipment manufacturer’s lubrication instructions rather than using a general quantity.

9. How should the grease be stored?

Keep the product in its original sealed container in a clean, dry environment. Follow the manufacturer’s storage and shelf-life recommendations, and protect the grease from dust and moisture.

10. What should be checked before purchasing 47560118001 39218193?

Verify the complete product designation, the 39218193 lubricant reference, container label, required lubricant specification, and applicable equipment model. Confirm the package dimensions and shipping weight with the supplier.

Procurement and Maintenance Recommendations

When purchasing Ingersoll Rand 47560118001 39218193 High Temperature Grease, the most important step is confirming that the lubricant matches the equipment’s maintenance requirements.

The 39218193 reference is identified as Ingersoll Rand high-temperature motor grease. Buyers should verify the complete product designation and packaging information, particularly because the relationship between the supplied prefix 47560118001 and the lubricant reference should be confirmed against the actual package label or parts documentation.

For industrial maintenance departments, it is useful to keep lubricant references separate from filter, valve, and mechanical spare-part records. This helps prevent incorrect substitutions during scheduled servicing.

During storage and handling, keep the grease sealed and use clean dispensing equipment. Avoid mixing unverified lubricant types and follow the specified quantity and service interval.

The supplied dimensions of 95 × 95 × 80 mm and weight of 0.40 kg can be used as initial listing information. Confirm the actual container and gross shipping weight before dispatch.

Conclusion

The Ingersoll Rand 47560118001 39218193 High Temperature Grease is listed as an industrial motor lubrication product associated with Ingersoll Rand compressor maintenance. The confirmed lubricant reference, 39218193, is identified as high-temperature motor grease and is associated with Mobilith SHC 220 in relevant equipment information.

Its correct application depends on the motor’s lubrication requirements, operating frequency, bearing design, and maintenance procedure. Verifying the lubricant reference before use helps reduce the risk of incompatible grease selection and supports consistent industrial equipment maintenance.

For replacement-parts procurement, retaining the complete product designation and checking the actual container label are important steps in ensuring that the correct lubricant is supplied for the intended equipment.