Product Overview

The Ingersoll Rand 24900458 Oil Filter Element is a replacement filtration component designed for compatible industrial air compressor lubrication systems. It is also identified in some product catalogs as a coolant filter element. Its primary function is to remove solid contaminants from the compressor’s circulating lubricant before the fluid returns to critical components.

In rotary screw air compressors, lubricant performs several important functions. It helps lubricate moving components, supports heat transfer, and contributes to sealing within the compression process. During operation, the lubricant may collect dust, wear particles, oxidation products, and other contaminants. If these particles remain in circulation, they can contribute to component wear, reduced heat-transfer performance, and increased maintenance requirements.

The 24900458 filter element helps maintain lubricant cleanliness by capturing contaminants as fluid passes through its filtration media. Regular replacement is important because accumulated particles gradually increase filter restriction and can affect the performance of the lubrication circuit.

This part number is associated with selected Ingersoll Rand compressor models, including certain RS90ie, RS110ie, RS132i, RS132ie, RS160i, and RS160ie units. Compatibility should always be confirmed using the compressor model and serial number because equipment configurations can vary.

The supplied product dimensions are 118 × 118 × 364 mm, with a weight of 2.54 kg. These physical specifications are useful for product identification, inventory management, and shipping preparation.

Technical Specifications

Specifications are based on the supplied product information and available product references. Confirm the exact filter configuration and replacement interval against the compressor’s serial-number-specific documentation.

Function and Working Principle

The Ingersoll Rand 24900458 filter element operates as part of the compressor’s lubricant circulation system. It removes suspended contaminants from the fluid before the lubricant continues through the equipment.

1. Removal of Solid Contaminants

During compressor operation, particles can enter the lubricant through normal wear, environmental contamination, and fluid degradation. The filter media captures these particles as lubricant passes through the element.

Maintaining clean lubricant helps reduce the circulation of abrasive contaminants through components such as bearings, rotors, and other lubricated surfaces.

2. Protection of Compressor Components

Lubricant cleanliness is important for the reliability of a rotary screw compressor. Contaminated fluid can increase wear and contribute to deposits or restrictions in the lubrication circuit.

By retaining particles within the filter media, the 24900458 helps protect downstream components from avoidable contamination-related damage.

3. Support for Lubrication Circulation

The filter must allow sufficient lubricant flow while retaining contaminants. As particles accumulate, the pressure drop across the element may increase.

Replacing the filter at the appropriate service interval helps maintain the intended flow characteristics of the lubrication system. A heavily restricted filter can affect system operation and should not be left in service beyond the equipment manufacturer’s requirements.

4. Support for Thermal Management

In many oil-injected rotary screw compressors, lubricant also carries heat away from the compression process. Maintaining the cleanliness and circulation of the lubricant supports the overall thermal-management arrangement.

The filter does not replace the compressor’s oil cooler or temperature-control devices. Instead, it contributes to the condition of the fluid circulating through the system.

Role in Industrial Air Compressor Systems

The 24900458 is a maintenance component rather than an electronic control device. Its performance nevertheless affects the operating condition of the compressor and the reliability of the wider compressed-air installation.

Lubrication Circuit Protection

The filter is installed in the compressor’s designated lubricant filtration circuit. It helps remove contaminants before the lubricant reaches components that depend on clean fluid for lubrication and cooling.

Compressor Reliability

A suitable replacement filter helps maintain the filtration performance expected by the compressor design. Using the correct part number reduces the risk of installation problems caused by incorrect dimensions, sealing arrangements, or flow characteristics.

Maintenance Planning

The filter is a consumable item that should be included in the compressor’s preventive-maintenance schedule. Maintenance personnel can coordinate its replacement with lubricant servicing, air-filter replacement, and other scheduled inspection work.

Equipment Lifecycle Management

For industrial facilities operating multiple compressors, accurate spare-parts identification is important. Recording the filter part number, compressor model, serial number, and replacement date helps maintenance teams manage inventory and avoid incorrect substitutions.

Compatible Industrial Applications

The Ingersoll Rand 24900458 is associated with selected compressor models. Its application should be verified against the exact machine configuration.

1. Ingersoll Rand RS90ie Compressors

The 24900458 is listed for selected RS90ie compressor configurations. In this application, the filter supports lubricant cleanliness within the compressor’s circulation system.

2. Ingersoll Rand RS110ie Compressors

The filter is also listed for certain RS110ie units. Before ordering, confirm the installed compressor’s serial number and the required maintenance-part specification.

3. Ingersoll Rand RS132i and RS132ie Compressors

Selected RS132i and RS132ie configurations use the 24900458 filter element. Correct filtration supports the lubrication system and helps protect internal compressor components.

4. Ingersoll Rand RS160i and RS160ie Compressors

The part is also associated with selected RS160i and RS160ie compressor models. Because compressor configurations may differ by production period and equipment specification, model-name matching alone is not sufficient for final confirmation.

5. Industrial Compressed-Air Installations

These compressors may be used in manufacturing plants, processing facilities, workshops, and other industrial environments where compressed air supports production equipment.

The filter contributes to compressor maintenance rather than directly filtering the compressed air delivered to the plant. Compressed-air treatment may require separate aftercoolers, moisture separators, and line filters.

Installation and Replacement Guidelines

Correct filter replacement is important for maintaining the compressor’s lubrication performance and preventing contamination from entering the system.

1. Confirm the Correct Part Number

Before installation, check the existing filter label, compressor model, serial number, and parts documentation. Confirm that 24900458 is the correct replacement for the particular machine.

Do not rely only on approximate dimensions. Thread specifications, sealing surfaces, internal flow arrangements, and filtration characteristics must also match.

2. Shut Down and Isolate the Compressor

Stop the compressor and follow the manufacturer’s shutdown procedure. Isolate the electrical supply and allow the equipment to cool as required.

Follow the machine’s pressure-relief and lockout procedures before opening any part of the lubrication circuit. Never remove a filter while the system is pressurized or hot.

3. Remove the Used Filter

Prepare a suitable container and absorbent materials to collect residual lubricant. Remove the existing filter using the recommended service method.

Inspect the filter housing and sealing surface. Remove old gasket material where applicable and check for contamination, damage, or unusual deposits.

4. Install the Replacement Element

Compare the replacement element with the removed component. Confirm the dimensions, connection details, and sealing arrangement.

Install the new filter according to the manufacturer’s instructions. Avoid excessive tightening, which can damage the sealing components or housing.

5. Restart and Inspect

After installation, restore the system according to the compressor’s commissioning procedure. Check for leaks and verify that the compressor operates normally.

Observe relevant pressure, temperature, and filter-condition indicators. If abnormal pressure drop, leakage, or operating alarms appear, stop the machine and investigate before returning it to normal service.

Compatible System Components

The 24900458 operates as part of a wider compressor maintenance system. The following components may be relevant when planning service work.

These items are separate compressor components and are not necessarily included with the 24900458 filter element.

Alternative Models and Replacement Considerations

When replacing the 24900458, the safest approach is to confirm the exact OEM part number and equipment compatibility. Similar dimensions do not guarantee equivalent filtration performance.

Cross-reference listings should be treated as identification aids rather than automatic approval for substitution. For critical compressor installations, use the manufacturer’s confirmed replacement part or obtain written compatibility confirmation from the supplier.

Key Advantages

Effective Lubricant Filtration

The filter element captures suspended contaminants from circulating lubricant, helping maintain the cleanliness required by the compressor system.

Protection for Internal Components

Reducing the circulation of abrasive particles helps protect lubricated compressor components from avoidable contamination-related wear.

Support for Preventive Maintenance

The replaceable element can be incorporated into planned service intervals, helping maintenance teams manage compressor consumables systematically.

Compatibility with Selected Ingersoll Rand Compressors

The 24900458 is listed for selected RS90ie, RS110ie, RS132i, RS132ie, RS160i, and RS160ie configurations. Final compatibility should be confirmed by serial number.

Practical Spare-Part Identification

The part number and physical dimensions provide useful information for purchasing, warehouse management, and maintenance planning.

Technical FAQs

1. What is the Ingersoll Rand 24900458?

It is an oil or coolant filter element used in selected Ingersoll Rand industrial air compressors. It removes contaminants from circulating lubricant to help protect the compressor’s internal components.

2. Which compressors use the 24900458 filter?

Available product references list selected RS90ie, RS110ie, RS132i, RS132ie, RS160i, and RS160ie compressors. Confirm compatibility with the equipment serial number before purchasing.

3. What are the dimensions of the 24900458?

The supplied dimensions are 118 × 118 × 364 mm. Check the actual product and its dimensional drawing before using these values for installation planning.

4. What is the weight of the filter?

The supplied product weight is 2.54 kg. Packaging and shipping weight may be different.

5. How often should the filter be replaced?

Some product references recommend replacement at approximately 4,000 operating hours or every six months. The actual interval depends on the compressor model, operating environment, lubricant condition, and manufacturer’s maintenance schedule.

6. What happens if the filter is not replaced?

Contaminants continue to accumulate in the filter media, potentially increasing flow restriction. A restricted or damaged filter can affect lubricant circulation and may contribute to abnormal compressor operation.

7. Is the 24900458 an air filter?

No. It is identified as an oil or coolant filter element. It is used in the compressor’s lubricant circuit, not as the primary intake-air filter or a compressed-air line filter.

8. Can an aftermarket filter be used?

An aftermarket element may be suitable if its dimensions, sealing arrangement, filtration performance, flow capacity, and operating specifications match the OEM requirements. Confirm equivalence before installation.

9. Is the 47639432001 number the same as 24900458?

The relationship between these two numbers should be confirmed using the original packaging, supplier documentation, or the compressor’s parts list. The filter description in this article is based on the identifiable 24900458 part number.

10. What should be checked before ordering?

Confirm the compressor model, serial number, existing filter part number, dimensions, connection details, and required filtration specification. Also check whether the item is genuine OEM or an aftermarket replacement.

Procurement and Maintenance Recommendations

When purchasing the Ingersoll Rand 24900458, begin by confirming the part number against the compressor’s parts documentation. The same compressor family may contain different configurations depending on production date, operating conditions, and equipment options.

For spare-parts procurement, request clear product photographs, packaging information, and confirmation of the part number. If the item is supplied as an aftermarket equivalent, request its technical data and cross-reference documentation.

During maintenance, record the installation date and operating hours. Inspect the compressor for abnormal temperature, pressure, or leakage conditions, and replace the filter according to the equipment manufacturer’s requirements.

For industrial facilities with several compressors, keeping a documented stock of essential filter elements can help reduce maintenance delays. Accurate part identification is particularly important when managing multiple compressor models or older equipment.

Conclusion

The Ingersoll Rand 24900458 Oil Filter Element is a compressor maintenance component designed to remove contaminants from circulating lubricant in compatible industrial air compressors. It supports lubricant cleanliness and helps protect internal compressor components from contamination-related wear.

With supplied dimensions of 118 × 118 × 364 mm and a weight of 2.54 kg, the filter can be identified for purchasing and inventory purposes. Its use in selected RS90ie, RS110ie, RS132i, RS132ie, RS160i, and RS160ie models should be confirmed against the compressor serial number and applicable parts documentation before installation.