Product Overview

The Ingersoll Rand 47560107001 39218193 High Temperature Grease is an industrial lubrication product associated with Ingersoll Rand compressor and motor maintenance applications. The lubricant reference 39218193 is identified in product listings as Ingersoll Rand Motor Grease and is also associated with Mobilith SHC 220.

Proper lubrication is essential for rotating machinery. Electric motor bearings and other specified lubrication points operate under continuous mechanical loads, friction, and temperature changes. Using the correct grease helps maintain a suitable lubricating film between moving surfaces, reduce wear, and support reliable equipment operation.

In industrial compressed-air systems, motor reliability directly affects compressor availability. Bearings that operate without suitable lubrication may experience increased friction, temperature rise, vibration, and premature wear. Using the lubricant specified for the equipment helps maintenance personnel follow the manufacturer’s service requirements.

The 39218193 grease is intended for applications where this lubricant specification is approved. It should not be treated as a universal substitute for every compressor grease, bearing lubricant, or air-compressor coolant. Grease compatibility depends on the bearing design, operating temperature, load, lubricant chemistry, and manufacturer’s maintenance instructions.

The supplied product dimensions are 95 × 95 × 80 mm, with a listed weight of 0.40 kg. These values can be used as the initial product-listing information, but the actual container size and shipping weight should be confirmed before dispatch.

Technical Specifications

Note: The specifications above distinguish the confirmed 39218193 lubricant identity from the supplied catalog and package information. Verify the container label and current technical data sheet before relying on detailed physical or performance specifications.

Function and Working Principle

High-temperature grease performs several important functions in rotating machinery. It forms a lubricating film between moving surfaces, helps reduce friction, and provides protection against wear under the conditions for which it is formulated.

1. Bearing Lubrication

Electric motor bearings support rotating shafts and help maintain accurate alignment during operation. As the shaft rotates, the bearing elements move against their raceways.

A suitable grease provides lubrication between these contact surfaces. The lubricating film helps reduce direct metal-to-metal contact and supports smooth bearing operation.

For applications specifying 39218193, maintenance personnel should follow the equipment manufacturer’s lubrication instructions, including the required grease quantity and relubrication interval.

2. Friction and Wear Reduction

Friction is unavoidable in mechanical systems, but appropriate lubrication helps control it. Grease forms a protective layer between contacting surfaces, reducing resistance to movement and limiting wear.

This is particularly important in industrial motors that operate for extended periods. Continuous operation can place substantial demands on bearings, making correct lubricant selection and maintenance essential.

3. Thermal Stability

Motor bearings may experience temperature changes caused by operating speed, mechanical load, ambient conditions, and internal friction.

A grease formulated for demanding temperature conditions is intended to maintain useful lubrication properties within its specified operating range. However, no lubricant should be assumed suitable for unlimited temperatures.

The actual operating temperature limits must be checked against the current technical data sheet and the motor manufacturer’s requirements.

4. Corrosion and Oxidation Protection

Industrial bearings may be exposed to moisture, air, and contaminants. Suitable grease can help protect bearing surfaces from corrosion and slow lubricant deterioration caused by oxidation.

The degree of protection depends on the grease formulation and the operating environment. Proper sealing and contamination control remain necessary.

5. Lubricant Retention

Unlike liquid lubricants that circulate through a dedicated system, grease can remain within a bearing housing or lubrication point. Its consistency helps it stay in the intended location during operation.

Correct grease quantity is important. Excessive grease can increase bearing temperature and churning resistance, while insufficient grease may result in inadequate lubrication.

Role in Industrial Compressor Systems

Industrial compressors depend on several rotating components, including electric motors, shafts, bearings, and drive assemblies. These components must operate reliably to maintain compressed-air production.

The Ingersoll Rand 39218193 grease is associated with specified motor lubrication requirements. Its role is to support bearing maintenance where the equipment documentation calls for this lubricant.

Motor Bearing Maintenance

Electric motor bearings carry mechanical loads while allowing the rotor to rotate. Proper lubrication helps reduce friction and wear during continuous operation.

When a compressor motor is serviced, technicians should identify the bearing type, lubrication points, and recommended grease before applying lubricant. The 39218193 reference should be used only where the applicable maintenance documentation specifies it.

Compressor Reliability

A motor bearing problem can affect compressor operation and may eventually result in equipment downtime. Planned lubrication helps maintenance teams address bearing requirements before excessive wear develops.

Using the correct grease as part of a scheduled maintenance program supports consistent servicing and reduces the risk of lubricant incompatibility.

Preventive Maintenance Planning

Compressor maintenance is commonly organized around operating hours, equipment condition, and manufacturer recommendations. Lubrication tasks should be recorded together with inspections, filter replacement, and other scheduled service activities.

The maintenance interval for 39218193 should be determined by the specific compressor or motor documentation rather than by applying a universal interval.

Industrial Applications

1. Electric Motor Bearing Lubrication

The grease is associated with electric motor lubrication applications where 39218193 is specified. Motor bearings require suitable grease to maintain a lubricating film under operating loads and temperatures.

Before application, confirm the motor manufacturer’s bearing-lubrication instructions and the required grease quantity.

2. Industrial Air Compressor Maintenance

Ingersoll Rand compressors use different maintenance procedures depending on model, motor design, and production configuration. The 39218193 lubricant reference appears in compressor-related motor maintenance information.

Maintenance personnel should verify the exact compressor model and lubrication specification before ordering or applying the product.

3. Rotary Screw Compressor Service

Rotary screw compressor installations often operate for long periods and depend on reliable motor and rotating-component performance. Motor bearing lubrication is one part of the broader preventive-maintenance program.

The grease should only be used at lubrication points approved for this product. It is not a substitute for compressor coolant or air-end lubricant.

4. Industrial Fan and Pump Motors

Some industrial fan and pump motors use grease-lubricated bearings. The suitability of 39218193 for these applications depends on the bearing manufacturer’s requirements and lubricant compatibility.

Do not assume that a grease specified for one compressor motor is automatically suitable for every fan, pump, or electric motor.

5. General Industrial Machinery

Industrial machinery may contain bearings that require grease lubrication under elevated temperatures or continuous operating conditions. Correct grease selection helps support mechanical reliability.

The equipment documentation should always determine whether this specific Ingersoll Rand lubricant is appropriate.

Installation and Lubrication Procedures

Grease application should be performed by qualified maintenance personnel using the equipment manufacturer’s instructions.

1. Identify the Lubrication Point

Before applying grease, identify the bearing or lubrication point and confirm that 39218193 is the specified lubricant.

Check the equipment nameplate, maintenance manual, lubrication chart, and any grease identification label attached to the motor.

2. Confirm Grease Compatibility

Do not mix different grease types unless compatibility has been confirmed. Greases with different base oils, thickeners, or additive systems may not be compatible.

If the existing grease is unknown, consult the equipment manufacturer or a qualified lubrication specialist before introducing a new product.

3. Prepare the Lubrication Area

Clean the grease fitting and surrounding area before servicing. Dirt and moisture entering a bearing can cause damage even when the correct grease is used.

Use clean tools and suitable dispensing equipment. Keep the grease container closed when it is not being used.

4. Apply the Correct Quantity

Use the quantity specified by the motor or bearing manufacturer. Avoid overgreasing because excessive grease can increase friction, temperature, and bearing churning.

If the motor has a grease relief port or a specific relubrication procedure, follow the manufacturer’s instructions carefully.

5. Observe Equipment Safety Procedures

Before maintenance, isolate the equipment from its power source and follow the applicable lockout/tagout procedure. Verify that the machine cannot start unexpectedly.

Allow hot components to cool where necessary and use appropriate personal protective equipment.

6. Record Maintenance Activities

After servicing, record the lubricant part number, quantity applied, date, operating hours, and equipment identification.

Accurate maintenance records help technicians track lubrication intervals and identify recurring bearing problems.

Compatible System Components

The 39218193 grease is a maintenance consumable rather than an electrical or mechanical control module. It is used alongside the equipment and maintenance tools required for approved lubrication procedures.

These items are associated with the lubrication process and are not necessarily included with the grease product.

Alternative Models and Replacement Considerations

Lubricants should not be replaced based only on similar descriptions such as high-temperature grease or motor grease. Compatibility must be established through the equipment manufacturer’s requirements and the lubricant technical data.

The references above are not interchangeable alternatives for every application. Some compressor maintenance instructions distinguish lubricant requirements according to motor frequency or motor configuration.

Before substituting a lubricant, compare:

• Base oil type.
• Thickener chemistry.
• NLGI consistency grade.
• Operating temperature range.
• Bearing speed and load.
• Water resistance and corrosion protection.
• Compatibility with the existing grease.
• Motor manufacturer’s approved lubricant list.

Key Advantages

Manufacturer-Referenced Lubricant

The 39218193 part number provides a specific reference for identifying the Ingersoll Rand motor grease used in applicable maintenance procedures.

Support for Bearing Maintenance

Suitable grease helps maintain lubrication between bearing contact surfaces and supports reliable operation under specified conditions.

Temperature-Oriented Formulation

The product is identified as high-temperature grease, making its approved temperature range an important factor when selecting it for the intended application.

Helps Control Mechanical Wear

A suitable lubricating film helps reduce friction and wear in approved bearing applications.

Useful for Planned Maintenance

Keeping the correct lubricant available helps maintenance teams complete scheduled motor servicing without relying on unverified substitutes.

Clear Spare-Parts Identification

Using the correct part number helps distinguish the specified lubricant from other Ingersoll Rand compressor oils, coolants, and grease products.

Technical FAQs

1. What is Ingersoll Rand 39218193?

Ingersoll Rand 39218193 is a high-temperature motor grease used in specified industrial lubrication and compressor motor maintenance applications.

2. What is the relationship between 47560107001 and 39218193?

The supplied product designation includes both references. The 39218193 number identifies the grease itself. The exact contents and role of the 47560107001 reference should be confirmed against the supplier’s package label or parts documentation.

3. Is 39218193 associated with Mobilith SHC 220?

Yes. Available product information associates Ingersoll Rand 39218193 with Mobilith SHC 220 motor grease. Confirm the container label and current product documentation before use.

4. What is high-temperature grease used for?

High-temperature grease is designed to maintain lubrication under specified elevated-temperature conditions. It helps reduce friction and wear in compatible bearings and other approved lubrication points.

5. Can 39218193 be used in every Ingersoll Rand compressor?

No. Compressor models and motor configurations can have different lubrication requirements. Check the equipment’s maintenance manual and motor lubrication label before application.

6. Can it be used as compressor coolant?

No. Grease and compressor coolant serve different purposes. The 39218193 product is identified as motor grease and should not be substituted for compressor coolant or air-end lubricant.

7. Can it be mixed with another grease?

Do not mix it with another grease unless compatibility has been confirmed. Different thickener and base-oil combinations may cause changes in consistency and lubrication performance.

8. How often should the grease be applied?

The relubrication interval depends on the motor, bearing type, operating speed, temperature, and service conditions. Follow the applicable manufacturer’s maintenance instructions.

9. What happens if too much grease is applied?

Overgreasing can increase bearing temperature and churning resistance. It may also cause grease leakage or damage seals in some designs. Apply only the quantity specified by the equipment manufacturer.

10. What should be checked before purchasing?

Confirm the complete part number, product label, lubricant designation, package size, condition, and compatibility with the intended motor or compressor. For critical equipment, request the relevant product documentation.

Procurement and Maintenance Recommendations

When purchasing Ingersoll Rand 47560107001 39218193 High Temperature Grease, verify the complete product designation and confirm that 39218193 matches the lubricant required by the equipment.

Check the package label and lubricant documentation to confirm the product identity. Do not rely solely on a general description such as high-temperature grease, because industrial lubricants with similar names can have different formulations and applications.

For inventory management, store grease in its original sealed container in a clean and dry environment. Follow the manufacturer’s storage and shelf-life recommendations. Prevent dust, moisture, and other contaminants from entering the container during handling.

During maintenance, use clean dispensing tools and record the lubricant quantity and service date. Avoid mixing unverified grease types, and investigate abnormal bearing temperature, vibration, noise, or grease leakage rather than attempting to solve every issue by adding more lubricant.

The supplied dimensions of 95 × 95 × 80 mm and weight of 0.40 kg should be checked against the actual package before shipment. Net product weight and gross shipping weight may differ.

Conclusion

The Ingersoll Rand 47560107001 39218193 High Temperature Grease is an industrial lubrication product associated with specified Ingersoll Rand motor and compressor maintenance applications. The 39218193 reference is identified as motor grease and is associated with Mobilith SHC 220.

Correct lubricant selection is important for bearing performance, temperature management, and long-term equipment reliability. Before using this product, maintenance personnel should verify the compressor or motor requirements, confirm grease compatibility, and follow the manufacturer’s lubrication procedures.

For industrial spare-parts procurement, retaining the complete product reference and checking the actual package label helps ensure that the correct lubricant is supplied for the intended maintenance application.