Company Information
E-mail		[email protected]
Mobile		+8615980777398
Whatsapp		+8615980777398
WeChat		15980777398

Product Overview

The Ingersoll Rand 47623602001 / 85574374 Hose is an industrial replacement hose designed for use with compatible compressor equipment and associated fluid or air-system assemblies. Flexible hose components are important in industrial compressor systems because they provide connections between equipment sections while allowing appropriate movement, vibration absorption, and easier maintenance access.

The supplied hose length for Ingersoll Rand 85574374 is 38 inches, while the listed shipping weight is 3 kg. These specifications are important when identifying replacement parts, planning compressor maintenance, organizing spare-parts inventory, and preparing transportation requirements.

The reference combination 47623602001 / 85574374 should be retained when sourcing this component. Although hoses used in compressor systems can appear similar, differences in length, connection configuration, application, and operating requirements can make otherwise similar components unsuitable as substitutes.

The exact hose material, internal diameter, end fitting configuration, pressure rating, temperature rating, and media compatibility have not been specified here and should be confirmed against the original installation and applicable equipment documentation before replacement.

---

Technical Specifications

Parameter	Specification
Manufacturer	Ingersoll Rand
Reference Number	47623602001
Part Number	85574374
Product Type	Hose
Application Category	Compressor Replacement Part
Hose Length	38 in
Shipping Weight	3 kg
Typical Application	Compatible industrial compressor systems
Installation	Compressor-system hose connection
Replacement Requirement	Verify complete part number and system configuration

Technical note: The supplied 3 kg value is the shipping weight and should not be treated as the net weight of the hose. Exact hose construction and operating specifications should be verified for the specific compressor application.

---

What Is the Ingersoll Rand 85574374 Hose?

The Ingersoll Rand 85574374 is a replacement hose associated with reference 47623602001.

Hoses in industrial compressor systems are used to create flexible connections between components that may experience vibration or relative movement during operation.

A generalized compressor connection can be represented as:

Compressor Component → Flexible Hose → Compressor Component

The actual position of the 85574374 hose depends on the compressor model and the circuit in which it is installed.

Depending on its intended location, a compressor hose may be associated with air, oil, cooling, control, or another designated circuit. The exact service should therefore be confirmed before installation.

---

Function of the Hose

Flexible Equipment Connection

The primary mechanical advantage of a hose is its flexibility.

Unlike rigid piping, a flexible hose can accommodate a certain amount of movement between connected assemblies when correctly selected and installed.

Vibration Accommodation

Rotary screw compressors contain rotating mechanical equipment that can generate vibration.

A suitable hose can help accommodate normal vibration within the limits of its intended design.

Simplified Maintenance

Flexible connections can make equipment maintenance more practical by allowing components to be disconnected without modifying permanent rigid piping.

System Fluid or Air Transfer

Depending on the original installation, the hose may form part of a circuit used to transfer a designated medium.

The exact medium handled by 85574374 should be confirmed from the compressor configuration rather than assumed from the general term “hose.”

---

Importance in Compressor Maintenance

A hose is a relatively simple component, but its condition can influence the reliability of the compressor system.

Hose deterioration may result in:

• Leakage
• Pressure loss
• Fluid loss
• Contamination
• Reduced system performance
• Equipment shutdown
• Secondary component damage

For this reason, hose inspection should form part of routine compressor maintenance.

---

Hose Length and Installation Planning

The specified hose length is:

38 in

Length is a critical identification characteristic when replacing a compressor hose.

A replacement that is too short can create excessive tension at the connection points. A hose that is excessively long can create unnecessary loops, contact with surrounding components, or additional abrasion points.

During replacement, technicians should compare the new hose with the original installation and verify:

• Overall length
• Routing path
• Connection positions
• End orientation
• Bend requirements
• Clearance
• Support arrangement

The 38 in length should be considered together with the complete physical routing of the original hose.

---

Industrial Applications

Screw Compressor Systems

The 85574374 can be used as a replacement hose within a compatible Ingersoll Rand compressor configuration.

Industrial Compressed-Air Systems

Compressed-air equipment is widely used throughout manufacturing plants.

Hoses and other replacement components help maintain the mechanical and fluid connections required for reliable compressor operation.

Manufacturing Facilities

Factories often depend on compressed air for pneumatic actuators, tools, control equipment, production machinery, and material-handling systems.

Maintaining compressor components can help minimize unplanned downtime.

Compressor Service Operations

During planned maintenance or compressor overhaul, hoses can be inspected and replaced when they show signs of deterioration or damage.

Industrial Utility Equipment

Compressed-air systems are frequently treated as essential industrial utilities. Reliable hose connections contribute to the overall integrity of the compressor installation.

---

Installation Guidelines

Before replacing the Ingersoll Rand 85574374, follow the appropriate compressor shutdown and maintenance procedure.

1. Shut Down the Compressor

Stop the compressor using the normal operating procedure.

2. Isolate Energy Sources

Disconnect or isolate electrical and other relevant energy sources before beginning maintenance.

3. Depressurize the Circuit

Compressed-air and fluid systems can retain stored pressure after shutdown.

The relevant circuit must be safely depressurized before disconnecting the hose.

4. Confirm the Part Number

Verify the replacement against:

47623602001 / 85574374

5. Inspect the Existing Installation

Record the original routing, connection orientation, and support points before removing the old hose.

6. Inspect Connection Points

Check fittings, seals, ports, and surrounding components for damage, contamination, corrosion, or wear.

7. Install the Replacement

Install the replacement hose without twisting or forcing it into position.

8. Check Hose Routing

Ensure that the hose does not interfere with moving or rotating equipment.

9. Pressurize and Inspect

After assembly, restore the system gradually and inspect the hose and connections for leakage.

---

Hose Routing and Mechanical Protection

Correct routing is one of the most important factors affecting hose service life.

The hose should not be subjected to unnecessary mechanical stress.

Avoid:

• Excessive bending
• Twisting
• Stretching
• Crushing
• Sharp-edge contact
• Continuous abrasion
• Contact with moving components
• Unsuitable heat sources

The 38 in hose should follow a routing path that provides adequate clearance while maintaining a natural installation shape.

If the original hose shows unusual wear at one location, technicians should investigate the underlying cause rather than simply installing a replacement.

---

Inspection and Condition Monitoring

A compressor hose should be visually inspected during scheduled maintenance.

Look for:

Surface Cracking

Cracks can indicate deterioration and should be investigated before they develop into leakage or complete failure.

Abrasion

Repeated contact with brackets, piping, cabinet structures, or other components can damage the outer surface.

Deformation

Unusual swelling, flattening, or permanent deformation can indicate mechanical or operating problems.

Leakage

Any visible leakage should be investigated promptly.

Connection Damage

Fittings and connection points should be inspected together with the hose body.

---

Troubleshooting Guide

Hose Leakage

Possible causes include:

• Hose deterioration
• Damaged connection
• Seal failure
• Incorrect installation
• Mechanical damage
• Excessive operating conditions

Inspect both the hose and the associated connection.

Premature Hose Wear

If the hose wears out significantly earlier than expected, check:

• Routing
• Vibration
• Abrasion
• Bending
• Temperature exposure
• Mechanical support

Repeated failures may indicate an installation problem rather than a defective replacement part.

Hose Does Not Fit Correctly

If the replacement cannot be installed naturally, verify:

• Complete part number
• Hose length
• Connection arrangement
• End orientation
• Compressor model
• Installation routing

Do not force an incorrectly matched hose into position.

Connection Continues to Leak

If leakage remains after replacing the hose, inspect the fitting, sealing elements, connection surface, and alignment.

A damaged fitting may need attention before the hose can operate correctly.

Hose Contacts Other Components

Unwanted contact can cause abrasion or heat damage.

The routing should be corrected so that the hose remains clear of moving, sharp, or excessively hot components.

---

Preventive Maintenance

Inspect Hose Condition

Include hose inspection in routine compressor maintenance.

Check Connections

Inspect fittings and connection points for leakage or mechanical deterioration.

Check Routing

Confirm that vibration has not changed the original hose position.

Monitor Compressor Operation

Abnormal vibration, temperature, or pressure conditions may contribute to hose deterioration.

Replace Damaged Components Promptly

A hose showing serious damage should be evaluated and replaced according to the maintenance requirements of the compressor system.

Maintain Spare Inventory

For critical compressor installations, maintaining replacement hoses in inventory can reduce downtime during maintenance.

Record the full identification:

47623602001 / 85574374

---

Shipping Weight and Spare-Part Logistics

The supplied shipping weight is:

3 kg

This value should be used for shipping, transportation, and logistics planning.

It should not be interpreted as the net weight of the hose.

For inventory management, record:

• Reference number
• Part number
• Hose length
• Quantity
• Shipping weight
• Compressor application
• Storage location

The 38 in length should also be clearly recorded to distinguish this hose from similar compressor hose assemblies.

---

Replacement Considerations

When sourcing a replacement for the Ingersoll Rand 47623602001 / 85574374 Hose, the complete identification should be checked carefully.

The supplied specifications are:

• Reference: 47623602001
• Part Number: 85574374
• Hose Length: 38 in
• Shipping Weight: 3 kg

Additional characteristics should be verified before installation, including:

• Hose construction
• Internal diameter
• End fittings
• Connection type
• Pressure requirements
• Temperature requirements
• Media compatibility
• Bend requirements
• Compressor model

These characteristics should not be inferred solely from the part number.

---

Compatible Compressor System Components

A typical industrial screw compressor system may include:

Component	Typical Function
Compressor Element	Compresses air
Hose Assembly	Provides flexible connection
Oil Filter	Filters compressor oil
Air Filter	Filters intake air
Air-Oil Separator	Separates oil from compressed air
Cooler	Controls operating temperature
Valves	Regulates air or fluid flow
Sensors	Monitors operating conditions
Control System	Manages compressor operation
Electrical System	Supplies and controls equipment power

The actual configuration varies by compressor model.

---

Related Ingersoll Rand Replacement Components

Reference / Part	Product Type	General Function
47623601001 / 24900433	Oil Filter	Compressor oil filtration
47623601001 / 47605764001	Panel Air Filter	Air filtration
47623601001 / 23708423	Air-Oil Separator	Air/oil separation
47623601001 / 88089743	Breathing Filter	Compressor system filtration
47623601001 / 24900318	Air Filter	Air filtration
47623601001 / 24266058	Hose	Flexible compressor connection
47623601001 / 24266207	Hose	Flexible compressor connection
47623601001 / 24266215	Hose	Flexible compressor connection
47623601001 / 24266223	Hose	Flexible compressor connection
47623601001 / 85574374	Hose	Flexible compressor connection
47623602001 / 85574374	Hose	Flexible compressor connection

Related hose components should not be substituted solely because they have similar lengths or appearance.

---

Storage Recommendations

Replacement hoses should be stored in a clean and suitable environment.

Avoid unnecessary exposure to:

• Direct sunlight
• Excessive heat
• Moisture
• Chemicals
• Sharp objects
• Mechanical compression

The hose should be stored in a manner that avoids permanent deformation or sharp bends.

Keep the identification label or packaging associated with the part whenever possible.

---

Key Advantages

• Ingersoll Rand industrial compressor replacement component
• Suitable for compatible compressor-system applications
• Supplied hose length of 38 in
• Identified by part number 85574374
• Associated reference 47623602001
• Flexible connection for industrial equipment
• Useful for compressor maintenance and overhaul
• Supports practical spare-parts management
• Supplied shipping weight of 3 kg
• Suitable for industrial compressor service planning

---

Technical FAQs

What is the Ingersoll Rand 85574374?

The Ingersoll Rand 85574374 is identified as a Hose associated with reference 47623602001.

What is the hose length?

The supplied hose length is 38 inches.

What is the shipping weight?

The supplied shipping weight is 3 kg. This value is for shipping and logistics purposes and should not be treated as the net component weight.

What is the function of a compressor hose?

A compressor hose provides a flexible connection between compatible equipment or system assemblies and can accommodate appropriate movement and vibration.

Can this hose be installed on any Ingersoll Rand compressor?

No. Compatibility should be confirmed using the complete 47623602001 / 85574374 identification and the specific compressor configuration.

What should be checked before installation?

Verify the complete part number, hose length, connection arrangement, fittings, routing, pressure requirements, temperature requirements, and media compatibility.

Why is the 38 in length important?

Hose length affects installation routing and mechanical stress. A hose that is too short or excessively long may not provide the intended connection geometry.

What can cause premature hose failure?

Potential causes include abrasion, excessive bending, twisting, vibration, heat exposure, incorrect routing, unsuitable operating conditions, or incorrect hose selection.

Is the 3 kg value the actual hose weight?

No. The supplied specification identifies 3 kg as the shipping weight.

How should the replacement part be identified?

Verify both:

47623602001

and

85574374

The 38 in hose length should also be checked against the original installation.

---

Conclusion

The Ingersoll Rand 47623602001 / 85574374 Hose is an industrial replacement hose associated with compatible compressor equipment. Flexible hose assemblies play an important role in compressor systems by providing practical connections between components while accommodating appropriate equipment movement and vibration.

The supplied hose length is 38 inches, which should be carefully checked during replacement to ensure correct routing and avoid excessive mechanical stress. The supplied 3 kg shipping weight is relevant to transportation and spare-parts logistics and should not be interpreted as the net weight of the hose.

Proper replacement involves shutting down and isolating the compressor, safely depressurizing the relevant circuit, verifying the complete part number, inspecting connection points, installing the hose without twisting or excessive bending, checking routing, and performing a controlled leak inspection after reassembly.

For reliable maintenance, the complete Ingersoll Rand 47623602001 / 85574374 identification should be verified before ordering or installation. Exact hose construction, fittings, pressure rating, temperature rating, and media compatibility should be confirmed for the intended compressor system rather than assumed from the general product description.